How To Build A Computer, Lesson 1

How To Build A Computer, Lesson 1

how to build a computer

All of the again ports ought to match into the holes in the I/O backplate.Use the screws provided to safe the motherboard to the standoffs through the shielded screw holes on the motherboard. You may need to put in and wire your case’s fans before you possibly can install any components. If so, observe your case’s fan installation directions. You’ll use this to connect the hard drive to the motherboard later.

Motherboards

Each power provide cable will solely match in the right orientation, but pressure will still be wanted to push the cables in. If using a newer energy provide with an 8-pin EPS 12V connector and a PCI Express eight-pin connector, don’t try to force the cables into place. Yes, when you want to run that OS you’ll have to go into the BIOS or boot choice menu to inform the computer to boot from a specific onerous drive. If you’re keeping a hard drive from an old computer, ensure it is appropriate with the new parts and attempt to do a contemporary install of the OS to wipe out any bloatware. Windows 10 purchased from a store or on-line comes on flash drive now, all you must do is plug in the flash drive and boot from that.

how to build a computer

Cases might obstruct air circulate causing some higher-end components with bigger power draw to overheat. Be certain to select a case which might match all of your parts, together with your onerous drive. A dedicated graphics card is essential for playing the most recent video games, but not a major concern for a computer you propose on using for daily tasks. If you watch or edit lots of HD video or play plenty of video games, you’ll need a devoted graphics card. Hard drives also can use IDE instead of SATA as their connections, however SATA is newer and thus supported on all fashionable motherboards. This wikiHow teaches you the way to build a desktop computer utilizing customized elements.

The energy supply will normally go close to the top or the bottom rear of the case. You can determine where the power provide is supposed to take a seat by on the lookout for a lacking part on the again of the case.

However, you should still go to the manufacturers’ product pages for your components to ensure you have or get the newest updates. Lastly, there are the tiny entrance-panel connectors, including power, reset, HDD exercise light, and so forth. Sometimes you’ll discover it at the top, however it’s often mounted at the backside, where it can pull in cool air from underneath the chassis.

Refer to the cooling system’s set up instructions so as to take action. Plug the hard drive’s SATA cable into the SATA slot on the motherboard. Remove any front panels on the case (when you’re putting in an optical drive, you’ll usually set up it near the top of the case). Once the standoffs are put in, place the motherboard within the case and push it up towards the backplate.

Successfully constructing a computer is essentially contingent on defining your computer goals and budget, buying the proper elements, and placing every thing collectively in the correct order. @techyinaz Andrew actually had a mention of that in there and I took it out as a result of I was on the fence about it, significantly for first-time builders. Installing SATA power/knowledge earlier than mounting the drive might work in some instances, however I’d suspect most individuals could be better off mounting the drive and then connecting cables. Once you’ve got put in your operating system, whenever you first connect with the web, Windows 10 is fairly good nowadays at getting device drivers.

  • You’ll additionally use the cable that came with the optical drive to attach it to the motherboard (align the red stripe for “pin 1”) and plug the other end into the drive.
  • Just as with the hard drive, you need to use any obtainable connector from the ability supply.
  • Again, there’s an apparent place for it to plug in on the motherboard and on the drive itself.

You also can download the ISO and, using Microsoft USB Download Tool software, create your individual bootable set up flash drive when you have a spare. Once your operating system is put in, you will need to put in your drivers.

Once you place it in place, it’s typically as simple as screwing it into place with four screws at the back of the case. Then, plug in the 24-pin energy connector and supplemental/CPU power connector into the motherboard.